Regulator khusus Ghost warrior pcp predator

Regulator khusus Ghost warrior pcp predator


Assalamualaikum warahmatullahi wabarakaatuh May you all be in the protection of an almighty God, and be given health This time I will deliver How to install the paintball regulator on the air gun pcp unit Ghost warrior made in Indonesia This is already installed My manometer moved here Back position This is a valve burst disk This is for high pressure and low pressure If you see the design does not allow regulators to be installed Must add Reducer connection And modify Cover the front from the air tank tube Let’s follow the installation method. This is a shotgun construction This reducer turns the screw facing the chamber And smaller thread size From thread regulator 5/8 ” Thread diameter around 16 mm with a screw distance of 1.5 mm We try, put the spin first From the tube Nah like this Then we open it Close the tube This is the model and The thread is smaller The 5/8 “paintball regulator thread Smaller diameter of thread around 16mm Look, can’t enter If this one can but must use a connection reduser This 16 mm With 1.5 mm alley While this one is 21 Or thread 5/8 If we pair it, we can’t If we use the connection, it will Getting longer And do not enter This one is 5/8 He is 21 mm and chamber he is 16 The only thing by installing This reducer And the right size fits Because this is indeed for ghost warriors Same size And the one behind This can enter And for the purpose Klop can enter We try While the front What goes into the tube is m18x1.5 mm We open first The coupler And inside it There is an Oring seal Then open it the manometer Enter, accordingly We try To assemble it See the distance becomes long Around 75 mm or 7.5 cm So we must Cut the front cover With a mini bibut machine After that it was drilled With a drill he is 16 mm And Continue with turning inside, okay done And use a chisel inside More or less Diameter 16 mm Fit 16 mm in size Then make the thread with a tap of the hand M 18 x 1.5 mm complete we spray it first to be clean Done We test Well … enter easily The thread is m18 x 1.5 mm Okay Done Good! We are released again After this we clean the machine With vacuum cleaner This is the result, right? OK, bagua Then we set it Before total assembling Looks appropriate We prepare the pipe tube This is a diameter of 50 mm Duralium aluminum material And 6mm thick So it’s quite safe from high pressure And surface reducer because it’s not flat with the chamber Must be leveled first It’s a distance of 7.5 cm This is the result So the regulator is installed Previously, we will test first The regulator and Output pressure 1800 psi And expect 1000 fps of power Okay take care Good work perfect see 1800 psi This is a problem The coupler And manometer The position is not appropriate Then we modify And changed We will install the quick coupling We will put the manometer in the BLUE chamber Now Reducer we flatten Same with the surface of the chamber block So that the meeting and not tenuous Next we can close the hole To close the manometer hole With brass only With solid material Made M10 x1mm As per the manometer thread We are snai We form By making a groove for a screwdriver so that it’s easy We made the plug with a seal system use oring, so that easy and not easy to leak Done, then make a key flow With mini grinder dremmel So that the pair is easy Yes, this is the result we Will attach with a screwdriver Don’t ignore leaks For the manometer we made it Reducer too Because the ghost warrior’s thread design is Using M12 threaded So we make the reducer to M10x1mm We installed it then the manometer OK, bagua Then we test With high pressure Hopefully good Apparently there was a small leak We see now This is a paintball regulator This is a reducer This is closed OD tube 50 mm This is a modification By making additional threads I cut it so that it’s not long This is the mark These are valves Low pressure burst disk This is high pressure Instead I closed it For manometer I move it in the chambet block This actually can also be installed manometer Only later Main pressure manometer, It’s in front of this tube High pressure And low pressure here Now we see Once again Reducer, 5/8 goes to 16 mm This is 18×1.5 maauk OK !! New ghost warrior with Use a paintball regulator perfectly mounted Okay, let’s follow the test Ghost warrior predator pcp Test with a chronograph Wow … great 978.5 fps With regulator pressure 1800 psi Successful and successful Thank you

12 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *